In my downloads, I have IONIFWpackage1.4.0.gdf and IONIFW-1.5.4.gdf.
So I guess it was IONIFW-1.5.4.gdf but not sure of anything.
I was also using MMosForceFeedback2014
Before going to bed, I just did a little promenade on Imola. It works flawlessly. Thanks again to all of you!
You are the expert so if you say so it will stay like this and i will enjoy my wheel!
Thanks a lot for your assistance!
mtakala Sorry I had a too long day in front of my computer... Now yes see it and guess what? No more error.
But I guess this feature shouldn't be at Do nothing
mtakala My english should be ok.
I did not get your last suggestion. Which limit function are you talking about? Is it in granite?
Stef Bord j'ai essayé 8A pour MCC et 12A puis 12.5A pour MMC. Pas de changement.
I've lowered the MMC and MCC following your recommendation. No improvement...
I've noticed that after the start the wheel has some constant resistance. It is bizarre as the driver is in error state...
J'ai essayé le FEV =10000, MCC et MMC a différentes valeurs mais cela ne marche toujours pas.
Le volant fait un mouvement pour se calibrer et je suis en erreur.
Aussi Measure resistance and inductance ne fonctionne pas => Measurement failed. Ensure that all required conditions are met. Je suppose que c'est du au fait que je sois en permanent stop
Je viens de faire le test à 50,51 et 52V. Pas mieux.
Bonjour,
J'étais sur MMos et je viens de vous rejoindre sur SimuCUBE. Tout c'est bien passé grâce aux info trouvés sur le forum.
J'ai roulé au moins 5 tours sur le Nürburgring. Je passe sur Imola et là dans un virage spécifique coupure du FFB 
Je trouve l'excellent post AC- Réglage RFR Wheel By Pascal 71 avec tous les indications nécessaires.
Depuis la mise à jour des paramétres dans Granite le volant ne marche plus.
Dans Simucube, j'ai le message Overvoltage threshold [FOV] must be > 102% of HV BUS voltage
Dans Granite, a la connexion, j'ai la pop up "Some recently changed parameters or faults require drive restart (Permanent stop state is on). Do you want to restart device now?"
Mon alimentation est en 48v 12.5A
J'ai mis le FOC au max comme suggéré page 42
Une idée de la source de mon problème?
Merci pour votre aide
DEVICE STATE
[ ] Initialized !
[ ] Error recovering
[ ] Tracking error warn
[ ] Target reached
[X] Enabled
[ ] Run (drive active)
[ ] Homing active
[ ] Braking
[X] Permanent stop !
[X] Voltages good
[X] Fault stopped !
[ ] Ready for use
[ ] STO active
[ ] Tracking error
[ ] Over velocity
[ ] Hardware
[ ] Over temperature
[ ] Feedback
[ ] Over current
[ ] Internal comm error
[ ] Power stage forced off
[ ] Under voltage
[ ] Over voltage
[ ] Motion range
[ ] Firmware error
[X] Init !
[ ] Motion
[X] SimpleMotion !
What caused this fault?
Fault location ID1 6602 (info)
Fault location ID2 0 (info)
! = reasons for inactivity[X] GPI 1
[X] GPI 2
[X] GPI 3
[ ] GPI 4
[X] GPI 5
[ ] GPI 6
[ ] HSIN 1
[ ] HSIN 2
[ ] ANA1 as digital
[X] ANA2 as digital
[X] ENC A
[X] ENC B
[ ] ENC C
[ ] ENC D
[X] Hall U
[X] Hall V
[ ] Hall W
[X] Soft enable
[X] Phys enable
[ ] Pos feed enable !
[ ] Neg feed enable !
[X] Home switch
[ ] Clear faults
Analog in 1 0.04 V
Analog in 2 0.00 V
Analog Enc A 3.66 V
Analog Enc B 3.65 V
HV bus voltage 47.8 VDC
Device temperature 23 °C
Actual current limit ±12.0 A
Last limit reason None
Output current 0.00 A
Velocity feedback 0 r/s
Velocity feedback (raw) 0
Position feedback 0.0001 r
Position feedback (raw) 1
Setpoint value (raw) 0
Debug 1 -1
Debug 2 -1
Debug 3 -1
Debug 4 -1
Debug 5 -1
Debug 6 -1
Parameters
| GCFWVER=10700 | HWTYPE=11001 | HWSERIAL=110011564 | BUILDREVISION=4897cde
| CEI=2 | UID=21800304 | SMO=0 | TRF1=0
| TRF2=0 | TRA1=0 | TRA2=0 | MPP=590
| NOTCHFILT=655616 | TED=0 | TEF=0 | TEI=0
| SERIALENCBITS=6 | COMMUTATIONCFG=0 | HAO=0 | FBR=2500
| FBD=1 | FB2D=0 | TBW=5 | KVP=2200
| KVI=30 | KPP=50 | VFF=0 | AFF=0
| PFF=85 | CM=2 | MT=3 | AD=0
| FLAGS=131092 | MMC=12 | MCC=12 | FOC=6
| FOV=49 | FUV=30 | FPT=1000 | FVT=100
| FEV=140 | FMO=0 | LSF=1 | AXS=1
| AXT=3 | FFT=0.1 | TSR=15 | TCH=126
| TTR=1 | TBT=0 | CRI=3 | DIV=100
| PIF=2500 | MUL=100 | CAL=32 | CSD=10
| CVL=1400 | CRV=100 | MR=2.616 | ML=8.188
| MTC=2300 | MPC=8 | MMS=1000 | CAO=0
| HOMING=0 | HMV=100 | HMA=10 | HMH=500
| HMT=1 | HHL=0 | HLL=0 | HMF=0
| HSA=0 | HSS=0 | overrideAddr1=0 | overrideAddr2=0
| overrideAddr3=0 | overrideVal1=0 | overrideVal2=0 | overrideVal3=0
| BED=1.5 | BER=0 | BDD=1 | CAPS1=4.19405e+06
| CAPS2=16287
lumière sur la IONI:
Fault reason Initialization
Motor control states Permanent stop (need device reset)
Ma config:
Granity version 1.14.0
Model Granite devices IONI Pro
HW type ID 11000
GraniteCore firmware version 1.7.0
firmware revision ID 4897CDE
petit mige
