Bonjour a tous ,Super idée S.Jaune. voici mes réglages pour un DD1 avec une roue F1 (dia 27cm) pour Iracing:
je les utilise en F3 qui a un FFB un peu particulier par rapport au GT3.
Sensitivity (SEN) – Auto
Force Feedback (FF) – 37
Sock (SHO) – 100
ABS (ABS) – 95
Force Effect (FOR) – 90
Spring Effect (SPR) – 100 (not used by iRacing)
Damper Effect (DPR) – 100 (not used by iRacing)
Natural Damper (NDP) – 15
Natural Friction (NFR) – OFF
Brake Force (BRF) – 45
Force Effect Intensity (FEI) – 100
in game :
Strength: 62Nm
Wheel force: 20Nm
Mode linear.
mes document dans le fichier app.ini , code du forum iracing
Code
[Force Feedback] allowXBoxOneOnWindows10=1 ; Set to 1 to talk to xbox one game pads on windows 10, warning the driver is buggy alwaysRestartFX=0 ; Always restart force when updating it, set to true if wheel goes limp after a while calibUsingRawData=0 ; Use raw joystick position over windows calibration data when detecting new joysticks centerSpringPct=-1 ; Percent (0-100) of static centering spring force to apply, -1 is off. Not reccomended for use. damperMode=0 ; Set damper effect type 0 = Damper 1 = Inertia 2 = Friction damperSaturation=10000 ; Set damper saturation from 0 to 10000 dampingSliderSetsFriction=1 ; True if damping slider adjust friction effect, false to adjust wheels built in damping effect debounceSeq_Ms=80 ; Add delay in Milliseconds to sequential shifter to reduce double shifts disableAutoCenter=1 ; Turn auto center off on all force feedback devices displayLinearInNm=1 ; Display the force level in peak Nm when using the linear mode enableFanatecWheelDisplay=1 ; Enable the use of Fanatec wheel displays enableG27WheelDisplay=0 ; Enable use of shift indicators on the G27 and clones enableHotPlug=1 ; Set to 0 to turn off usb hot plugging in case you have usb disconnect issues enableWheelDisplayBlink=1 ; Enable the display lights to blink when at the rev limit FFBUseSimpleMinForce=0 ; 0 - Use smoothed min force, 1 - use old sharp min force forceNoiseSuppression=0 ; Remove noisy joystick axis, even if they are calibrated by hand forceResetBeforeInit=1 ; Force a reset of the whole FFB system every time we create or destroy a FFB effect initOnlyNewDevices=1 ; Set to 0 to force all devices to reinitialize when a device change is detected invertFFBForce=0 ; Reverse the force feedback effects, if your wheel is spinning the wrong way reinitFanatecWheelDisplay=0 ; reinitialize the fanatec wheel display when reconnecting devices this may cause issues seperateXBox360Triggers=1 ; Set to 1 to seperate the XBox 360 joystick triggers into there own axes steerAverageSteeringTorque=0 ; True averages 360 Hz data down to 60 Hz, false uses last sample steeringBumpStop_Deg=100.000000 ; degrees into bump stop before max force steeringDampingFactor=0.050000 ; Damping factor adjust down if damping becomes unstable, defautlt to 0.05 steeringDampingMaxPercent=0.000000 ; Maximum amount of damping to apply, adjust this to set damping level, values between 0.05 and 0.2 are best, overriden by damping slider steeringDampingParkedMaxPercent=0.000000 ; Maximum amount of damping to apply when parked, adjust this to reduce wheel oscilation when parked, values between 0.05 and 0.30 are best steeringFFBSmooth=1.000000 ; Percent of current FFB force to use vs average force, 1.0 = no average 0.001 = max average steeringForceParkedPct=0.500000 ; Reduce FFB force by percent when parked, to help reduce oscillations je vais testé tes réglages pour AC , avec quel combo tu les a effectué?
