Faut que les spécialistes passent par là
DIY - Problème simucube Grosphilou / résolu
-
-
External Content www.youtube.comContent embedded from external sources will not be displayed without your consent.Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy.
voila ce que sa fait...
-
Cest très violent
-
ah ben oui je confirme
-
Ffb trop élevé ?
-
ben j'ai essayer sans réglage pareil.
j'ai le setup thomconcept sur granity, mais j'ai mis en 5000 ppr.
après je sais pas si sa vient de ce que granity envoie a la ioni ou si c'est de simucube
mais bon la c'est injouable
-
bon dans raceroom quand je mets "intensité des forces de rotation" a "0" ben je n'ai plus le problème mais c'est mou...
-
Essaie ces réglages
-
jai testé ça hier soir avec les lignes que tu as posté au dessus.
Mes doute se porte qur la conf granity du coup non?
-
Essaie ces réglages
je vois que tu es sur 15 À , ce n est pas trop élevé ou trop puissant ?
En ce qui me concerne , je suis sur 12 au maximum.
-
Je baisse le ffb dans le jeu
dans raceroom je suis a 35%
-
Oui mais prend en compte les réglages ffb du jeu également.
Je pense pas que ce soit ton problème mais à essayer.
Il faut certainement que tu modifies quelques réglages dans granity mais je n'y connais rien.
Tu devrais poster ici pour mtakala
DIY - SimuCUBE - Open-source Firmware progress and discussion
-
https://drive.google.com/open?id=1JUMtw…jaKrE5uzJQAOQdS
https://drive.google.com/open?id=1mZmiL…Xovy7HQOlI1tx4z
https://drive.google.com/open?id=1Hv-sr…G_ys0WWkcH9nwLb
https://drive.google.com/open?id=1QLP3_…TVKBDbEjGq-05BN
https://drive.google.com/open?id=1ww05V…Ny-0J3Y_SRZ7gzt
https://drive.google.com/open?id=1wQw62…XhZ8-anq-y3W5K5
voici mes réglages sur granity.
si quelqu'un peut m'indiquer si cela est cohérent avec le petit mige (130ST m10100) en 5000 PPR ?
-
Edit : (supprimé) j'ai dit des bêtises...
-
https://drive.google.com/open?id=1JUMtw…jaKrE5uzJQAOQdS
https://drive.google.com/open?id=1mZmiL…Xovy7HQOlI1tx4z
https://drive.google.com/open?id=1Hv-sr…G_ys0WWkcH9nwLb
https://drive.google.com/open?id=1QLP3_…TVKBDbEjGq-05BN
https://drive.google.com/open?id=1ww05V…Ny-0J3Y_SRZ7gzt
https://drive.google.com/open?id=1wQw62…XhZ8-anq-y3W5K5
voici mes réglages sur granity.
si quelqu'un peut m'indiquer si cela est cohérent avec le petit mige (130ST m10100) en 5000 PPR ?
Your MMC is overdriving the servo. Maximum rated current for small mige is 12.86 A.
You should put the maximum RPM to 1000 rpm, although I do not think it has any effect.
On Fault Limits tab, your Overvoltage Fault Threshold is quite high. Please put it close to 102% of the HV bus voltage. Usually 49.5 V or 50.0 V are fine.
If you really have a 5000 PPR encoder, then 5000 PPR in Granity is correct. CPR is the value you put to MMOS, and it is shown in the SimuCUBE Configuration Tool. CPR = PPR * 4.
-
-
Yes I deleted my message, I made the mistake...
-
je reste en 5000 PPR, car pas de MMOS c'est une simucube avec ioni
-
Your MMC is overdriving the servo. Maximum rated current for small mige is 12.86 A.
You should put the maximum RPM to 1000 rpm, although I do not think it has any effect.
On Fault Limits tab, your Overvoltage Fault Threshold is quite high. Please put it close to 102% of the HV bus voltage. Usually 49.5 V or 50.0 V are fine.
If you really have a 5000 PPR encoder, then 5000 PPR in Granity is correct. CPR is the value you put to MMOS, and it is shown in the SimuCUBE Configuration Tool. CPR = PPR * 4.
i do all change, but i have the same sensation...
-
Grosphilou Au fait, pour RaceRoom, faut que tu paramètres manuellement, la rotation du volant sous SimuCUBE afin de cadrer avec le jeu, l'as tu fait ?...
-